Micron MT40A1G8SA-062E:J 8Gb DDR4-3200 SDRAM

16 November 2026 68

Micron MT40A1G8SA-062E:J 8Gb DDR4-3200 SDRAM

The Micron MT40A1G8SA-062E:J is an 8Gb DDR4 SDRAM component organized as 1G × 8. It supports up to 3200 MT/s at a 1600 MHz clock, uses a nominal 1.2 V I/O supply, and comes in a 78-ball TFBGA package. Micron lists this exact revision as Obsolete. For an existing bill of materials, the sourcing decision starts with whether the build requires revision J or allows engineering to qualify another revision.

Illustrated Micron MT40A1G8SA-062E:J DDR4 package with 8Gb density, x8 organization, 3200 MT/s, 1.2 V, 78-ball TFBGA and CL22
DDR4 package illustration. Use the supplier’s lot photographs to verify actual device markings.

MT40A1G8SA-062E:J specifications

Parameter Specification
Memory type DDR4 SDRAM
Density and organization 8Gb, 1G × 8
Data rate and clock 3200 MT/s, 1600 MHz
CAS latency CL22 at DDR4-3200
Nominal I/O voltage 1.2 V
Package 78-ball TFBGA, 7.50 × 11.00 × 1.20 mm
Operating case temperature 0°C to +95°C (TC)
Micron lifecycle status Obsolete

Sources for the exact part: Micron obsolete DDR4 catalog and DigiKey part listing.

What the ordering code tells you

1G8 identifies the x8 organization, SA identifies the package, and -062E identifies the speed grade. The :J suffix identifies the die revision. Keep the complete ordering code on your BOM and RFQ, especially when your approved parts list specifies a revision. See the Micron 8Gb DDR4 SDRAM family datasheet.

Micron DDR4 ordering code breakdown showing MT40A family, 1G8 organization, SA package, -062E speed grade and J die revision
Ordering-code breakdown for the base device, package, speed grade and die revision.

Sourcing for an existing DDR4 design

For an OEM or EMS build using this exact part, ask for lot-specific evidence before booking material. When reviewing an alternative for an embedded board or memory module, start with the board’s approved BOM and memory-controller requirements.

  • Confirm the exact part. Request original packaging label and device-marking photos. Match the full ordering code, lot and date codes to the quote.
  • Confirm assembly requirements. Ask about packaging, storage and handling records, traceability documents, and any inspection requirements for your build.
  • Qualify a candidate on the target board. The Micron MT40A1G8SA-062E:R shares the published density, bus width, top data rate and package dimensions. Before approval, verify the ball map, supported timing points, refresh requirements and memory training on the target platform.

Frequently asked questions

How much memory does one MT40A1G8SA-062E:J provide?

Each device provides 8 gigabits of memory, equivalent to 1 GiB of raw capacity. Its x8 designation describes the device’s data bus width.

Why are 3200 MT/s and 1600 MHz both listed?

DDR transfers data on both edges of the clock. At 1600 MHz, two transfers per clock cycle yield 3200 MT/s. Actual operating speed depends on the controller and validated board configuration.

Is MT40A1G8SA-062E:J still in production?

Micron lists revision J as obsolete. If your BOM requires this revision, request lot-level availability, traceability and lead time for the quantity you need.

Request a quote for MT40A1G8SA-062E:J

Send your required quantity, delivery destination, target delivery date, and any date-code or traceability requirements. If engineering can review other revisions, include that in your inquiry so the exact part and candidate revisions can be quoted separately.