NT5CC256M16DP-DIH datasheet deep dive: key specs & pinout

25 October 2026 208

With a 4Gb density organized as 256M x16, low-voltage 1.35 V operation and support for up to 1600 Mbps data rate, the NT5CC256M16DP-DIH datasheet packs the key hardware constraints every embedded and board-level designer must master. This quick data-driven snapshot highlights capacity, organization, operating voltage and peak throughput to frame typical use cases and power/performance trade-offs.

This deep dive covers scope (key specs, pinout, package, timing and integration tips) for hardware engineers, firmware developers and procurement teams. It also references where to check the official datasheet figures for package drawings, timing tables and absolute limits—useful when validating a DDR3L 256Mx16 96-ball BGA pinout during selection or layout.

1 — Background & part overview (background introduction)

NT5CC256M16DP-DIH datasheet deep dive: key specs & pinout

1.1 Basic part identity and intended applications

Point: The device is a 4 Gb DDR3L low-voltage SDRAM with internal organization 256M x16. Evidence: The organization implies sixteen-bit wide DQ groups with banks and pages sized to 256M words. Explanation: This density suits embedded SoCs, industrial controllers and board-level modules where a 16-bit memory bus balances pin count and throughput; nominal Vcc at 1.35 V reduces power draw compared with legacy 1.5 V parts.

1.2 Package & thermal/grade variants at a glance

Point: The device ships in a 96-ball BGA family (VFBGA / PBGA96-style) with common commercial and extended temperature options. Evidence: Package drawings and ball maps in the official datasheet show a 96-ball footprint with typical ball pitch and dimension callouts. Explanation: Designers should confirm the exact mechanical drawing in the datasheet for footprint tolerances and pick the thermal grade that matches BOM and thermal budget for board-level reliability.

NT5CC256M16DP-DIH Pinout Diagram"> NT5CC256M16DP-DIH A0-A14 RAS/CAS/WE CS# / BA DQ0-DQ15 DQS+/DQS- DM CK/CK# VDD/VDDQ VSS/VSSQ

2 — Key electrical specs & operating limits (data analysis)

2.1 Power rails, I/O voltages, and static currents

Point: Core and I/O rails center on 1.35 V Vcc and Vccq, with multiple IDD operating and standby currents listed. Evidence: The datasheet IDD tables provide operating and precharge/refresh currents across speed bins and operating temperatures. Explanation: For worst-case power, sum active IDD plus refresh and I/O leakage, then add margin for DC/DC converter inefficiency and inrush during sequencing to size power supplies and thermal solution correctly (search for the IDD tables in the datasheet).

Parameter Symbol Min Typ Max Unit
Supply Voltage VDD 1.283 1.35 1.417 V
I/O Supply Voltage VDDQ 1.283 1.35 1.417 V
Operating Current IDD1 - Varies See DS mA
Standby Current IDD2P - Low See DS mA

2.2 Temperature, reliability, and AEC/Q or grade implications

Point: Operating temperature ranges normally cover commercial (-40°C to +85°C) with extended/automotive options available up to higher limits where specified. Evidence: The datasheet lists operating and storage ranges and any qualification notes regarding high-temperature tolerance. Explanation: Choosing a higher grade increases BOM cost and often changes screening/testing; map temperature grade to your environmental profile and manufacturing test flow early in procurement.

3 — Memory organization, capacity & performance (data analysis)

3.1 Logical organization, addressing, and density math

Point: 256M x16 organization maps to 4 Gb total (256M words × 16 bits). Evidence: Addressing uses row/column/bank fields; the datasheet provides row and column bit counts for translation. Explanation: For example, total bytes = (256M words × 16 bits)/8 = 512 MB. Controller address width must accommodate row+column+bank bits; consult the datasheet’s memory map to derive required address bus width and bank select settings.

3.2 Speed grades, timing and throughput (data rate)

Point: Supported data rates reach up to 1600 Mbps; timing tables in the datasheet map speed grade to CAS/tRCD/tRP values. Evidence: The device name and speed binning define maximum MT/s and recommended timing sets in the AC spec tables. Explanation: For example, 1600 MT/s commonly uses CAS 11 timing as a starting point while 1333 MT/s often runs CAS 9; pick the timing set matching your controller and validate with training sequences during bring-up. NT5CC256M16DP-DIH timing tables should be referenced for the exact supported combinations.

4 — Pinout & package pin map (case-display)

4.1 BGA96 pin map: power/GND/I/O grouping and critical pins

Point: The 96-ball map groups power and ground around the core with clustered DQ/DQS and address/command ball groups. Evidence: Typical ball maps in the datasheet show dedicated Vcc/Vccq banks, Vref locations and clock pairs. Explanation: Recognize these clusters for routing: place decoupling near Vcc balls, route DQS pairs with strict matching, and keep address/command nets short and direct to minimize timing skew and noise coupling.

4.2 Routing, escape, and footprint notes for PCB designers

Point: Routing strategy must prioritize decoupling, power planes and differential clock routing while planning BGA escape. Evidence: Mechanical and recommended layout notes in the datasheet list ball pitch, recommended pad sizes and keepout suggestions. Explanation: Use multiple power/ground planes, place bulk and local decaps adjacent to Vcc balls, length-match DQS to DQ within recommended tolerance, and implement thermal vias under the BGA to aid heat transfer and soldering reliability.

5 — Timing charts, AC/DC characteristics & reading the tables (method guide)

5.1 How to read AC timing diagrams and pick timing budgets

Point: Translate timing parameters (tCL, tRCD, tRP, tRAS) from datasheet tables into controller register values and timing budgets. Evidence: AC timing diagrams and numeric tables show relationships between command events and required windows. Explanation: Budget for timing by adding controller overhead (training, skew) to datasheet minima; for example, choose CAS and tRCD matching your target MT/s, then validate with eye/opening measurements during memory training.

5.2 DC characteristics: setup/hold, drive strength, and signal integrity considerations

Point: Setup/hold margins and recommended Vref/termination settings determine signal integrity headroom. Evidence: DC spec tables list setup/hold minima, VOH/VOL and recommended on-die termination values. Explanation: If training fails, verify setup/hold vs clock, adjust drive strength or termination, and use scope captures of DQS/DQ transitions to identify margin shortfalls; consult the datasheet for acceptable voltage thresholds and recommended termination schemes.

6 — Integration checklist & troubleshooting (action suggestions / method)

6.1 Pre-silicon checklist for BOM & board bring-up

Point: Pre-silicon validation reduces first-pass failures by confirming footprint, grade, and controller timing. Evidence: Datasheet sections on mechanical, electrical and sequencing provide required inputs. Explanation: Checklist items: verify exact BGA footprint, select temperature grade, map controller timing profile to datasheet AC sets, confirm power sequencing order and create test vectors for initialization and scrub operations prior to production.

6.2 Common failure modes & debugging steps

Point: Typical failures include boot hangs, training failures and persistent bit errors. Evidence: Troubleshooting flows often start with power rails and sequencing checks, then clock and address timing validation per datasheet limits. Explanation: Diagnose in order: validate Vcc/Vccq during power-up, check clock integrity and PLL lock, capture DQS/DQ during training to inspect eye margin, and cross-check address/command timing against datasheet setup/hold windows.

Summary

  • This part is 4 Gb organized as 256M x16 DDR3L operating at 1.35 V, offering up to 1600 Mbps of throughput—key for embedded and board-level memory needs.
  • Package is a 96-ball BGA with clustered power/GND and DQ/DQS groups; consult the official datasheet for the exact ball map and footprint tolerances before layout.
  • Power budget requires combining IDD active, refresh and I/O currents from the datasheet; plan worst-case margins for regulator sizing and thermal design.
  • Timing selection (CAS, tRCD, tRP) must align with speed grade—use datasheet AC tables and validate on-target timing during training and bring-up.
  • Pre-silicon checklist: verify footprint, select temperature grade, confirm power sequencing and prepare memory initialization vectors for early debug.

For definitive mechanical drawings, absolute maximum ratings and exact electrical tables consult the official datasheet when integrating NT5CC256M16DP-DIH into your design; those pages contain the authoritative pinout and spec tables.

Common questions & answers

What is the byte capacity and how does 256M x16 map to system memory?

256M x16 means 256 million words of 16 bits each: total bits = 256M × 16 = 4,096M bits, which equals 512 MB of usable storage. System mapping requires controller address lines sized to the datasheet’s row/column/bank bit-fields; verify the controller’s address muxing matches the part’s row and column counts.

Is the 96-ball BGA pinout compatible with other 4Gb DDR3L parts?

Pin-to-pin compatibility varies by vendor and specific ball mapping. While many 96-ball DDR3L devices use similar groupings (power, ground, address, DQ), you must compare the official pin map and mechanical drawing in the datasheet to confirm drop-in compatibility and avoid routing or sequencing mismatches.

What are the first checks if memory training fails at 1600 Mbps?

Start with power sequencing and rail levels, then verify clock integrity and PLL locking. Capture DQS/DQ during training to inspect eye opening; if margins are tight, try lowering speed to 1333 Mbps or relax CAS/timing settings per the datasheet. Review termination/Vref settings and ensure DQS-DQ length matching on the PCB.

Why is 1.35V Vcc preferred over 1.5V for this application?

The NT5CC256M16DP-DIH operates at 1.35V (DDR3L standard) compared to legacy 1.5V DDR3. This reduction significantly lowers dynamic power consumption and heat generation, which is critical for battery-powered embedded devices and thermally constrained industrial controllers. It also allows for simpler power supply design when mixed with other low-voltage logic rails.